Intellinet Wireless G Router Guida di Installazione

Introduction... 3 Features...

automatically and Obtain DNS server address automatically as shown on the following screen. 6: Click OK to confirm the setting. Your PC will

button to start installing the TCP/IP protocol. You may need your Windows CD to complete the installation. 5: After you install TCP/IP, go

3) Once you have configured your PCs to obtain an IP address automatically, the router’s DHCP server will automatically give your LAN clients an IP

can just configure the General Setup section, since the General Setup/WAN and the Quick Setup Wizard contain the same configurations. Status Informat

Control, Hacker Attack Prevention, DMZ, Special applications and other functions to meet your LAN requirements. Status Information (Chapter 3) In t

Chapter 1 Quick Setup The Quick Setup section is designed to get you using the broadband router as quick as possible. In the Quick Setup you are requ

Enable Daylight Savings The router can also take Daylight savings into account. If you wish to use this function, you must check/tick the enable box

Menu Description 1.1 Cable Modem Your ISP will automatically give you an IP address 1.2 Fixed-IP xDSL Your ISP has given you an IP address al

1.1 Cable Modem Choose Cable Modem if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional info

1.2 Fixed-IP xDSL Select Fixed-IP xDSL if your ISP has given you a specific IP address for you to use. Your ISP should provide all the information re

2.6.1 Access Control... 61 2.6.2 URL Blocking...

1.3 PPPoE Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the information required i

Connection Type If you select “Continuous”, the router will always connect to the ISP. If the WAN line breaks down and links again, the router will a

1.4 PPTP Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the information required in t

Subnet Mask Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0) Gateway Enter the IP address of the ISP Gateway User ID Enter the

Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You ca

Chapter 2 General Settings Once you click on the General Setup button at the Home Page, you should see the screen below. If you have already config

Below is a general description of what advance functions are available for this broadband router. Menu Description 2.1 System This section allow

2.1 System The system screen allows you to specify a time zone, to change the system password and to specify a remote management user for the broadba

Parameter Description Set Time Zone Select the time zone of the country you are currently in. The router will set its time based on your select

Parameters Description Current Password Enter your current password for the remote management administrator to login to your Broadband router.

Introduction Congratulations on purchasing this Wireless Broadband Router. This Wireless Broadband Router is a cost-effective IP Sharing Router that

Parameters Description Host Address This is the IP address of the host in the Internet that will have management/configuration access to the Br

Port The port number of remote management web interface. Enabled Select “Enabled” to enabl

2.2 WAN Use the WAN Settings screen if you have already configured the Quick Setup Wizard section and you would like to change your Internet connecti

2.2.8 DDNS You can specify a DDNS server that you wish to use and configure the user name and password provided by you DDNS service provider. Once you

2.2.5 L2TP Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP should provide all the information required in

Password Enter the Password provided by your ISP for the PPTP connection L2TP Gateway If your LAN has a L2TP gateway, then enter that L2TP gateway I

Parameter Description User Name Enter the User Name provided by your ISP for the Telstra Big Pond connection Password Enter the Password provid

convenience. If your Service Provider connects you to the Internet with dynamic IP settings, it is likely that the DNS server IP address is provided a

Parameters Default Description Enable/Disable Disable Enable/Disable the DDNS function of this router Provider

Parameters Default Description LAN IP IP address 192.168.2.1 This is the router’s LAN port IP address (Your LAN clients defaul

Get to know the Broadband Router Back Panel The diagram (fig1.0) below shows the broadband router’s back panel. The router’s back panel is divided i

DHCP Server Enabled You can enable or disable the DHCP server. By enabling the DHCP server the router will a

Parameters Default Description Enable or disable Enable You can select to enable or disable the wireless access point module of this rou

Parameters Default Description Alias Name The alias name of this router. ESSID default This is the na

Parameters Default Description Authentication Type There are two authentication types: "Open System" and "Shar

RTS Threshold When the packet size is smaller the RTS threshold, the wireless router will not use the RTS/CTS mechanism to send this packet.

Parameters Default Description WEP Mode Disabled You can select the WEP key length for encryption, 64-bit or 128-bit. Larger WEP

46

Parameters Default Description Key Format You may select to select ASCII Characters (alphanumeric format) or Hexadecimal Digits

64-bit WEP: input 10-digit Hex values (in the "A-F", "a-f" and "0-9" range) or 5-digit ASCII character as the encryption

2.5 NAT Network Address Translation (NAT) allows multiple users at your local site to access the Internet through a single Public IP Address or multip

Front Panel On the router’s front panel there are LED lights that inform you of the router’s current status. Below is an explanation of each LED and

Click on one of the three NAT selections and proceed to the manual's relevant sub-section. 50

2.5.1 Port Forwarding The Port Forwarding allows you to re-direct a particular range of service port numbers (from the Internet/WAN Ports) to a partic

Add Port Forwarding into the table Fill in the "Private IP", “Type”, “Port Range” and "Comment" of the setting to be added and t

2.5.2 Virtual Server Use the Virtual Server function when you want different servers/clients in your LAN to handle different service/Internet applic

Type Select the port number protocol type (TCP, UDP or both). If you are unsure, then leave it to the default both protocol. Public Port Enter the

Example: Virtual Server The diagram below demonstrates one of the ways you can use the Virtual Server function. Use the Virtual Server when you want t

2.5.3 Special Applications Some applications require multiple connections, such as Internet games, video conferencing, Internet telephony and others.

Public Type Select the Inbound port protocol type: “TCP”, “UDP” or both Comment The description of this setting. Popular applications This

router will allow incoming packets for ports 2300-2400 and 47624 to be directed to that user. Note: Only one LAN client can use a particular special

2.5.4 ALG Settings You can select applications that need “Application Layer Gateway” to support. Parameters Default Description Enable You can

Setup Diagram Figure 1.2 below shows a typical setup for a Local Area Network (LAN). Figure 1.2 6

2.6 Firewall The Broadband router provides extensive firewall protection by restricting connection parameters, thus limiting the risk of hacker attac

2.6.1 Access Control If you want to restrict users from accessing certain Internet applications/services (e.g. Internet websites, email, FTP etc.), th

Add PC Fill in “Client PC MAC Address” and “Comment” of the PC that is allowed to access the Internet, and then click “Add”. If you find any typo be

Client PC Description The description for this client PC rule. Client PC IP Addresses Enter the IP address range that you wish to apply this Access

Example: Access Control In the example below, LAN client A can only access websites that use Port 80. However, LAN client B is able to access website

2.6.2 URL Blocking You can block access to some Web sites from particular PCs by entering a full URL address or just keyword of the Web site. Param

You can now configure other advance sections or start using the router (with the advance settings in place)

2.6.3 Hacker Prevention The Broadband router's firewall can block common hacker attacks, including Denial of Service, Ping of Death, Port Scan an

2.6.4 DMZ If you have a local client PC that cannot run an Internet application (e.g. Games) properly from behind the NAT firewall, then you can open

Note: You need to give your LAN PC clients a fixed/static IP address for DMZ to work properly. You can now configure other advance sections or start

Getting started This is a step-by-step instruction on how to start using the router and get connected to the Internet. 1) Setup your network as sh

Chapter 3 Status The Status section allows you to monitor the current status of your router. You can use the Status page to monitor: the connection s

3.1 Status and Information The Status and Information section allows you to view the router’s system information Parameters Description Informa

3.2 Internet Connection View the Broadband router’s current Internet connection status and other related information Parameters Description Inter

3.3 Device Status View the Broadband router’s current configuration settings. The Device Status displays the configuration settings you’ve configured

3.4 Security Log View any attempts that have been made to illegally gain access to your network. Parameters Description Security Log This page sh

3.5 Active DHCP Client Table View your LAN client's information that is currently linked to the Broadband router's DHCP server Parameters

3.6 Statistics View the statistics of packets sent and received on WAN, LAN and Wireless LAN. Parameters Description Statistics Shows the count

Chapter 4 Tool This page includes the basic configuration tools, such as Configuration Tools (save or restore configuration settings), Firmware Upgr

4.1 Configuration Tools The Configuration Tools screen allows you to save (Backup) the router’s current configuration setting. Saving the configurati

4.2 Firmware Upgrade This page allows you to upgrade the router’s firmware Parameters Description Firmware Upgrade This tool allows you to upg

8: Reboot the PC. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please make sure that t

4.3 Reset You can reset the router’s system should any problem exist. The reset function essentially Re-boots your router’s system Parameters D

Appendix A How to Manually find your PC’s IP and MAC address 1) In Window’s open the Command Prompt program 2) Type Ipconfig /all and <ente

Glossary Bridge: A bridge is an intelligent, internetworking device that forwards or filters packets between different networks based on data link la

ISP Gateway Address: (see ISP for definition). The ISP Gateway Address is an IP address for the Internet router located at the ISP's office. ISP

Subnet Mask: A subnet mask, which may be a part of the TCP/IP information provided by your ISP, is a set of four numbers (e.g. 255.255.255.0) configur

5: Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server. Note: Please ma